Electrical Engineering · Georgia Tech '28

Peijie Liu designs density power, precision analog, and embedded hardware, then measures it.

EE junior at Georgia Tech with a Robotics minor, graduating December 2028. Specializes in Power Electronics, Precision Metrology, FPGA/ARM Embed, and Avionics/Robotics Integration. Avionics Hardware-in-the-Loop Lead at YJSP.

GPA at Georgia Tech
4.00
views on Bilibili
1M+
subscribers
~10K
LatestOn PyPINov 2026FirsthandThree open-source CLI / MCP tools that let Claude run a scope, multimeter and bench supply in real time.Read the write-up
Announcement
Seeking Summer - Fall 2027 Hardware Design Internships! Check out my Projects and Resume.

This website is now officially transfered to 🎊PEIJIE.DEV🎉 This causes a lost on traffic history, but solid upgrade it is!
Signal browserEvery build has a signature. Pick a channel.
Demo trace
ProjectOn PyPI2026

Firsthand

Three open-source CLI / MCP tools that let Claude run a scope, multimeter and bench supply in real time.

Sustained log
150 MB/s
1-ch stream
200 MSa/s
Hook lag, median
0.2 ms
Reaction time
~10 ms
Open the write-up
ProjectIn fabrication2026

USB to CAN / UART Hub

5 × 5 cm USB hub giving a Linux robot 4 CAN and 3 UART ports, with power-up sequencing to keep port order fixed.

Channels
4 CAN + 3 UART
Board size
5 × 5 cm
Stackup
4 layers
Open the write-up
ProjectIn layout2026

HITL SAM Board Tester

Three-board hardware-in-the-loop tester that emulates sensors and actuators to validate rocket avionics.

Components
1,206
DAC outputs
32 ch
ADC inputs
20 ch
Digital rail
5 V @ 10 A
Open the write-up
Project2026

μCHIMERA

Stackable solar, thermoelectric and piezoelectric energy harvester for battery-free medical devices.

Standby current
<1 μA
TEG min input
20 mV
Solar range
5 μW - 510 mW
Piezo output
88 mW RMS
Open the write-up
ProjectReleased2025

Super FDA

200 W fully differential Class AB amplifier with four switchable feedback modes and two input stages.

Output power
200 W
THD at -10 dBFS
-125 dB
Output swing
80 Vpp
Size
10×10×5 cm
Open the write-up
NoteFirst article2026

Servo Driver Shield

An Arduino Uno Q shield that powers 8 servos from one USB-C cable, with a Pico coprocessor for timing.

Servo rail
8.4 V @ 24 A
PD input max
28 V @ 140 W
Logic rail
5 V @ 10 A
Servo channels
8
Open the write-up
NoteFirst place2026

Mother-Daughter Rover

A quadruped rover that carries and launches a small scout rover, hand-wired on protoboard at a hackathon.

Build time
36 hours
Result
1st place
Servo rail
8.4 V 2S LiPo
Radio failsafe
200 ms
Open the write-up
NoteEngineering sample2025

GPSDO Mk.1

A friend's $30 GPS-locked 10 MHz OCXO reference, bench-tested here to 40 ppb or better.

Accuracy
40 ppb
Phase noise @1Hz
< -80 dBc/Hz
Output power
+12.06 dBm
Lock to ±20 ppb
~5 min
Open the write-up
NoteIn use2022

DAC729 R-2R Decoder

A non-oversampling audio DAC built on 1990s 18-bit Burr-Brown R-2R chips and discrete 74-series logic.

THD
-99.1 dB
Resolution
18-bit R-2R
Supply
USB-PD 20 V
Open the write-up
Super FDA - A 200W Fully Differential Class AB Amplifier with -135dB THD
μCHIMERA - Stackable Multi-Source Energy Harvesting System for Battery-Free Medical Devices
Building a Mother-Daughter Rover in 36 Hours - Circuit Notes from IEEE Robotech
DAC729 - Building a Vintage 18-bit Audio Decoder with 30-Year-Old Silicon
The Obsolete Oscilloscope: From Digital Outcast to Community Builder
Call Me a Risk-Taker
The Obsolete Oscilloscope
Letter to the Instructor: On Rhetorical Situations
This Community Is Essential
Why I Want to Revolutionize Hi-Fi
Post-Hackathon Iteration: Designing a Better Servo Driver Shield
Firsthand — A Bench Where Claude Can Sense Signals in Real Time
HITL SAM Board Tester — Hardware-In-The-Loop Avionics Validation System
GPS-Disciplined Oscillator (GPSDO) - Achieving 40ppb Accuracy
Multi-Channel USB to CAN / UART Converter — RoboMaster Control Interface